Career Market

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons Your fiat 500 stolen without keys 500 Key Fob Won't Work

A fiat 500 key fob is a great way to unlock the doors and get started the car. However, there are many reasons why the fob may stop functioning. This could be due to a dead coin battery, damage to the receiver module, water issues, or interference.

This listing is for an NEW replacement key for fiat 500 Fiat Flip Key Remote - like the Ilco brand that must be professionally programmed by a local locksmith (click here for Locksmith Search). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the most frequent cause of your 500 key fob that isn't working. Modern key fobs have limited operating range and must be within only a few inches from the vehicle in order to function. If you are further away from your vehicle, and you hit the keyfob, it will not respond, and display the message "Key Fob Not Detected".

If this occurs then replace the battery for your coin-cell (Part Number CR2032) with a new battery of a reputable brand such as Panasonic Duracell or Energizer. You can find them at the local hardware store or online.

You can test the battery of your coin-cell by pressing the buttons while standing close to your fiat 500 remote key programming 500. The car should blink its parking lights, and the key fob should operate the lock and unlock switches.

If the key fob doesn't function after replacing the battery, it could have water damage that prevents it from communicating with the receiver module in your car. Water damage can occur in a variety of ways, such as simply splashing or submerging the key fob saltwater at the beach. If you suspect that your fob was exposed to water, try putting it in a dry rice bag to draw the moisture out. If this does not work, you'll require your fob to be reset by an auto locksmith or a dealer.

Water Damage

The fob does have rubber seals to keep water out of the electronic chip inside, submerging it in the ocean or washing it in a machine could cause water damage. Saltwater can cause the circuit board to short and then cease to function. It's not good to get the fob wet but don't give up even if you accidentally drop the fob in water or fail to take it out of your pocket.

Remove the battery first. Clean the electronic chip with isopropyl or a similar product and dry it thoroughly before replacing the battery. Check the fob to determine if it's working. If the key still doesn't work, it might need to be reprogrammed. This is usually done by an auto locksmith or dealer.

If the key is older and hasn't been programmed to your car It will most likely need to be replaced completely. A professional automotive locksmith can complete this simple process. The locksmith will require the key cut to match the car's ignition. They will also need to program the fob into the system of your car. This is a fast and affordable process which can be completed the same day.

Receiver Module Issues

One of the main reasons your 500 key fob may stop functioning is because it's out of range. The remote typically has an operating range of 30 feet or less, and if it's too far away from your car it will not respond to your commands. This can easily be resolved by moving it closer to your vehicle until it begins responding.

If your fob won't work after replacing the battery for the coin, also called a "button", "watch" or "button" It may be due to a malfunction on the internal circuit board. In the majority of cases, reprogramming your fob will fix the issue. You can find directions on how to do this for most automobiles by searching YouTube or checking out the owner's manual.

It could be necessary to replace the metal clips that hold the coin batteries in their place. If they become loose, it can prevent your coin battery from being properly seated and cause your remote to malfunction.

In rare cases the fob could be out of alignment with your vehicle because of hardware or software problems. You can fix this problem by visiting your local dealer or auto-locksmith to reprogram your key fob. In some cases the software might require reinstallation in your body control modules.

Interference

In addition to a dead battery on a coin The key fob may not be able to transmit or receive signals due to interference. This could happen when the keyfob's location is in close proximity to a radio transmitter such as a cell phone or radar detector. Other reasons the key fob may not function include a poor connection to the buttons or damage to the internal chip, or water damage.

If the key fob been unable to function for a while suddenly, or after trying everything you can do at home to fix it e.g. replacing the battery, reprogramming it and using the spare key fob, you may have a malfunctioning receiver module on your 500. The receiver module, which is located beneath the dashboard, picks up radio frequency signals from your key fob. It transforms the signals into electronic commands which are then read by the vehicle.

There's a simple method to reset the 500's on-board system including the keyfob. Disconnect the 12 volt battery for approximately 15 minutes by removing the negative cable and then the positive cable. Reconnect the battery. This will clear out any remaining electricity and restart the car's computers. This can help the key fob to function again. If the problem persists you should seek out an experienced technician. They will be able to determine the root cause of any problems.